Sorry for the slow reply.
If you look at the specifications section at the bottom of this page: http://www.freetronics.com.au/pages/ste ... GXr6sN95hE it lists the StepDuino voltage specifications as:
7-28V DC recommended
5-40V DC maximum
I hope this helps!
Search found 21 matches
- Fri Dec 30, 2016 5:14 am
- Forum: StepDuino
- Topic: Voltage and Current
- Replies: 2
- Views: 1486
- Thu Dec 29, 2016 3:49 am
- Forum: EtherTen
- Topic: Ethernet.localIP() returns 0.0.0.0
- Replies: 1
- Views: 4405
Re: Ethernet.localIP() returns 0.0.0.0
Hi Ishikawaii,
Sorry for the very slow response. If you are still having problems just send us an email at support@freetronics.com and we can organise a replacement.
Regards, Daniel
Sorry for the very slow response. If you are still having problems just send us an email at support@freetronics.com and we can organise a replacement.
Regards, Daniel
- Mon Nov 07, 2016 12:35 pm
- Forum: Random Chit-Chat
- Topic: Need assistance from the gurus
- Replies: 3
- Views: 2320
Re: Need assistance from the gurus
Hi Keiran,
Could you be more specific about what sort of issues you were having?
Could you be more specific about what sort of issues you were having?
- Mon Nov 07, 2016 12:31 pm
- Forum: HBRIDGE: H-Bridge Motor Driver Shield
- Topic: Motor only spins in one direction
- Replies: 1
- Views: 3655
Re: Motor only spins in one direction
Hi AidanBlair,
Sorry about the slow reply. Did you manage to fix the problem? If not post a picture of your current set up and I will see if I can spot any issues.
Daniel
Sorry about the slow reply. Did you manage to fix the problem? If not post a picture of your current set up and I will see if I can spot any issues.
Daniel
- Mon Nov 07, 2016 12:29 pm
- Forum: ES: Ethernet Shield
- Topic: When will these be available again?
- Replies: 1
- Views: 4773
Re: When will these be available again?
Hi Treborjm87,
I don't know if we are planning on continuing to produce the Ethernet Shield. Our EtherTen is equivalent to an Eleven + and Ethernet Shield so this effectively replaced the need for an Ethernet Shield.
I don't know if we are planning on continuing to produce the Ethernet Shield. Our EtherTen is equivalent to an Eleven + and Ethernet Shield so this effectively replaced the need for an Ethernet Shield.
- Mon Nov 07, 2016 12:27 pm
- Forum: Module Discussion
- Topic: N-Drive Module heatsinking
- Replies: 1
- Views: 1810
Re: N-Drive Module heatsinking
Hi Mickc,
The MOSFETs shouldn't get TOO hot but obviously it will depend on how much current / voltage is going through it. I would suggest running the MOSFET under load, see how hot they get and then decide if you feel like you will need a heat sink or not. There is no hard and fast rule.
The MOSFETs shouldn't get TOO hot but obviously it will depend on how much current / voltage is going through it. I would suggest running the MOSFET under load, see how hot they get and then decide if you feel like you will need a heat sink or not. There is no hard and fast rule.
- Mon Nov 07, 2016 12:21 pm
- Forum: Project Showcase
- Topic: An audio player with an Arduino
- Replies: 1
- Views: 1550
Re: An audio player with an Arduino
Very cool!
- Mon Nov 07, 2016 12:20 pm
- Forum: HBRIDGE: H-Bridge Motor Driver Shield
- Topic: H-bridge cannot reset properly &how to stack two H-bridges together
- Replies: 1
- Views: 1867
Re: H-bridge cannot reset properly &how to stack two H-bridges together
Hi Dominix, This isn't a problem it is the way it is designed. At a really basic level that H-Bridge works by receiving commands from the Arduino telling it which way it should direct the motor outputs. Each H-Bridge is obviously identical meaning that when you stack the shields the same signals fro...
- Wed Oct 19, 2016 8:18 am
- Forum: RX315/RX433: 315MHz and 433MHz Receiver Shields
- Topic: 433MHz Receiver Shields + Arduino UNO help
- Replies: 1
- Views: 5004
Re: 433MHz Receiver Shields + Arduino UNO help
Hi ckyong,
Have a read of the getting started guide which can be downloaded from the bottom of this webpage. http://www.freetronics.com.au/products/ ... Acr9tB96VM
Hope that helps
Have a read of the getting started guide which can be downloaded from the bottom of this webpage. http://www.freetronics.com.au/products/ ... Acr9tB96VM
Hope that helps
- Wed Oct 19, 2016 8:15 am
- Forum: Module Discussion
- Topic: 9-DOF IMU
- Replies: 1
- Views: 683
Re: 9-DOF IMU
For anyone else wondering, this issue has been fixed. The classic case of using the wrong example code 
